Scan-and-Solve for Rhino

Simulate Early, Simulate Often... In Rhino

paolo ronca
  • mandello del lario
  • Italy
Share on Facebook Share

paolo ronca's Discussions

Constraints
13 Replies

more flexibility on constraints (ex. also rotation managemnt) will be added ?bye PaoloContinue

Started this discussion. Last reply by Mike Calvino Mar 7.

Loads type
4 Replies

did You plan to add thermal loads (temperature distribution over surfaces) ?if yes, can you anticipate rougly when this will be done ?regards PaoloContinue

Started this discussion. Last reply by Klaus Stickdorn Jan 26, 2014.

 

paolo ronca's Page

Latest Activity

Mike Calvino replied to paolo ronca's discussion 'Constraints'
"Is the edge constraint still available in the WIP?  I have not seen it in there."
Mar 3
Mike Calvino replied to paolo ronca's discussion 'Constraints'
"Wow!, this is great Michael! I'm glad I stumbled on this one. it will come in very handy. Thanks again for a great tool guys!"
Mar 2
Michael Freytag replied to paolo ronca's discussion 'Constraints'
"Rick, In Version 1.4, we've added the ability to restrain straight edges.  This should allow you to simulate pin joints after a few minor additions to your geometry: In this case, I've added a small square hole through the…"
Dec 21, 2011
young s. replied to paolo ronca's discussion 'Loads type'
"the thermal stress and deformation due to the thermal stress are very important issue in many industries. I hope you put this analysis capabilities on SnS slover,soon.  "
Mar 5, 2011
Richard.L replied to paolo ronca's discussion 'Loads type'
"Very glad to hear that,It’s very important, of course. Thermal ,thermo-structural and fluid mechanics are widely requested."
Jan 25, 2011
Rick Loheed replied to paolo ronca's discussion 'Constraints'
"Yes, fair prices for the Grail, I did not notice you had gone that far already, but I was hoping it would be around that level!  I am looking at models I might upload, most are 'proprietary' unfortunately but I have run some special…"
Jan 16, 2011
Vadim Shapiro replied to paolo ronca's discussion 'Constraints'
"Rick,  the prices for the initial version of Scan&Solve are already announced.  Look under the "Purchase" tab.    Where else can you get the  `Holy Grail'  at that price?   :-)    …"
Jan 16, 2011
Rick Loheed replied to paolo ronca's discussion 'Constraints'
"Vadim, call me Rick.  If you price it appropriately, to me what you have here is the 'Holy Grail'- as the engineering department went from calculators and working with draftsmen to creating virtual prototypes in 3D, I've worked…"
Jan 16, 2011
Vadim Shapiro replied to paolo ronca's discussion 'Constraints'
"Richard,  thank you for the suggestions on the restraints.  They are on the "future" list. Also,  we would love to see some solved problems,  particularly those that bring the "others" to their knees!  …"
Jan 15, 2011
Rick Loheed replied to paolo ronca's discussion 'Constraints'
"Pin joints would be my need for this... and it is important.  If you had a cylindrical surface it could be restrained 'normal to the surface' only but allowed to 'slide' rotationally or longitudinally. (For the interface,…"
Jan 14, 2011
Vadim Shapiro replied to paolo ronca's discussion 'Constraints'
"I see.  We have avoided introducing point  and edge restraints  because they are not physical.   They are also often requested by users, particularly those who are used to using mesh-based FEA solutions where restraints are…"
Jan 12, 2011
paolo ronca replied to paolo ronca's discussion 'Constraints'
"at first glange I would say the simplest way could be the possibility to constrain (X,Y,Z individually) not only surfaces but single points. In that way, with proper points choice, it would be possible to let or block any rigid body rotational…"
Jan 12, 2011
Vadim Shapiro replied to paolo ronca's discussion 'Constraints'
"This is an ongoing process:  we continually discuss what types of constraints may be added in Scan&Solve without overly complicating the simplicity of user interface.    If you have specific constraints in mind, and have some…"
Jan 11, 2011
Vadim Shapiro replied to paolo ronca's discussion 'Loads type'
"Thermal and thermo-structural analysis  are definitely on our roadmap.    However,   we prioritize our development  based on expressed user demand, and surprisingly there have not been many requests for thermo-structural…"
Jan 10, 2011
paolo ronca posted discussions
Jan 10, 2011
paolo ronca is now a member of Scan-and-Solve for Rhino
Jan 10, 2011

Profile Information

Occupation
Professional
Website Address
http://lafranconisilenziatori.com
What modeling, simulation and analysis tools do you use?
ANSYS

Comment Wall

You need to be a member of Scan-and-Solve for Rhino to add comments!

Join Scan-and-Solve for Rhino

  • No comments yet!
 
 
 

FOLLOW SCAN&SOLVE

© 2017   Created by Michael Freytag.   Powered by

Badges  |  Report an Issue  |  Terms of Service